Makita 9564CV vs 9565CV: My Real Test

Makita 9564CV vs 9565CV is a big choice. I use both of these hard tools. I will share my real tests with you. Let us look at how they work. The test will show you pure facts. I want to help you work smart. I know how to grind hard all day. Let us break down the traits one by one.

Makita 9564CV Angle Grinder

I took this tool to a bad job. I had to cut old iron pipes. The rust was thick and bad. I held the tool in my bare hands. It felt light. It is easy to hold. The grip is small. It fits me well. I turned it on with my thumb. It did not jump at all. The start was smooth and safe. I pressed the small wheel to the pipe. Sparks flew out. But the tool did not shake. It cut the old pipe fast. It was much faster than my old tool. The motor sound was strong. I used it in a tight spot. A big tool would not fit there. The four inch wheel is great.

You can buy these small discs anywhere. They cost less than big wheels. This saves you cash over time. I did ten cuts in a row. The tool did not care at all. It kept on cutting fast. The speed dial is at the back. I set it to max speed. It chewed through the hard rust. I also smoothed out bad welds. I turned the speed down for that. The soft wheel left a nice shine.

I used this tool for full weeks. I used it all day long. The tool did not get hot. Air vents kept the motor cool. This is a big deal. If a tool gets hot, it breaks. The cord is thick rubber. It stays soft in the cold. Cold cords get hard and snap. This one did not crack. I dropped it on hard stone. It bounced but did not break.

The green plastic is hard. The black gear case is solid metal. This tool is built to last. It is my top pick for daily cuts. I can use it with one hand. But two hands is more safe. The side handle screws tight. It gives you a firm grip. The gears still sound new.

Makita 9565CV Angle Grinder

I brought this tool to a big site. We had large steel plates to cut. We had big stone blocks to grind. I needed a tool that cuts deep. This tool has a five inch wheel. The motor is the exact same size. Both tools use the same parts inside. But this big wheel does more work. I cut into a thick metal beam. The large wheel sank deep in the steel. I did not have to stop. I did not flip the beam. This saved me a lot of time.

The tool feels strong in your hands. It pulls hard when it spins fast. You need to hold it tight. I used it to clean a huge floor. The wide disc covered a lot of space. It took off old paint fast. I ran it next to a cheap brand. The cheap one bogged down fast. This one kept spinning at full speed. It never lost power. It is a beast for big jobs.

I used it for hours on stone. White dust got all over the tool. It got on the switch and vents. But the tool kept running fine. It has a maze inside the body. This maze stops dust from ruining parts. I timed the speed of my cuts. It beat my old tool by ten minutes. That is a big win for a long day.

But, holding it high up is hard. The big wheel makes it feel heavy. My arms got tired after one hour. You feel the pull of the large disc. Still, for big jobs, it is the best. It takes less time to finish work. The metal guard covers a big space. It catches hot sparks well. I feel safe when I push it hard. I change the wheels a lot on site. The lock pin is big and easy. You push it down and turn the nut. The blade pops off fast.

Detailed Comparison for Makita 9564CV vs 9565CV

Let us look at both tools close up. I will show you how they compare. I test them on real tasks. I do not just read the specs.

Core Capability Comparison

Both tools do the same main jobs. They both cut, grind, and smooth parts. They both have a speed dial. You can turn it down to shine stone. You can turn it up to cut steel. They both do these tasks well. But their true skills are not the same. The small tool is for quick, tight work. The big tool is for heavy, deep cuts. You must pick the one that fits your task. I use the small one for thin pipes.

I use the big one for thick iron beams. The power feels the same in both. The motor has thirteen amps of juice. That is a lot of force. You will not lack power with either one. It just comes down to the reach. A big disc reaches much deeper. That small step makes a huge change. It means you cut a thick pipe at once.

Accuracy and Consistency

A good tool must cut a straight line. It should not shake or drift away. I tested both on a long mark. Which tool gives more stable results? The small tool is easy to guide fast. You can make short lines with it. But the big tool is best for long lines. The wide disc tracks straight in a deep cut.

It does not wander off the drawn line. Both tools keep a steady speed. They do not slow down when you push hard. They stay very strong all day. I drew a white line on a flat plate. I used the big tool to trace it. The cut stayed right on the chalk. I tried the same with the small tool. It moved a tiny bit. The small wheel can twist easier. So for pure straight cuts, go big. For quick curved cuts, go small. The big tool keeps a true, flat depth.

Design and Practical Use

The size and weight seem the same. They both weigh five pounds. But they do not feel the same at work. The small tool feels like part of your hand. It is very easy to flip around. You can use it fast in tight gaps. The big tool has a wide metal guard. It bumps into walls in tight rooms.

Tool A feels fine for long, hard use. Tool B makes your arms tired fast. The big wheel pulls hard when you move it. This is a real fact on the job. I had to work in a small dark box. The small tool fit right in. The big tool got stuck on the side walls. You need space to run a five inch disc. The grip feels the exact same on both. The barrel is slim and fits my palm. I do not drop them when my hands sweat. The cord comes out the back in a good spot.

Switches Interface and Usability

You must be able to use the tool in gloves. Work gloves are thick and stiff. The switch on both is a top slide type. It locks in place for long jobs. I can reach the switch with my thumb. It is easy to turn on and off. The speed dial is at the back base. You just roll it to change the speed. It has numbers from one to five. Both tools start up slow and soft. This keeps the tool from jerking your wrists.

It is a big win for your safety. I work outside in the cold a lot. Thick gloves are a must for me. The slide switch works great with thick gear. It clicks loud when it locks in. You know it is on for sure. When you press the back switch, it pops off. It stops the tool right away fast. The dial is stiff but moves well.

Safety Features and Build Quality

Safety is the top rule for tool tests. Grinders can kick back and hurt you bad. Both tools have a smart gear clutch. If the wheel gets stuck, the gears slip. This stops the tool from throwing you back. It also keeps the motor from burning up. The build quality is tough as nails. The cord is thick. The plastic is hard.

They both keep dirt out of the parts. I dropped both tools from a tall bench. They hit the floor hard and just scratched. Neither one broke or bent at all. I jammed a disc on purpose to test the clutch. The tool let out a loud zip sound. But it did not snap my arm back. The clutch works just like they say. It is the best trait on both tools. I feel safe knowing it is there. A cheap tool would break or hurt me.

Final Practical Table

Both tools do a great job on hard steel. The small wheel is for fast, tight work.