Klein 32559 vs 32560: Extended Reach Test

I tested both of these tools. I used them on real jobs for weeks. My old driver was too short. I needed more reach. Here is what I found.

Klein 32559 Review: Great For Home Use

I bought the Klein 32559 first. I do a lot of home repairs. My standard tool is good. But the shaft is thick. It is also too short. I tried to fix a dryer last month. The screws were deep in the back. My old tool could not reach them. I went to the store. I bought this long model.

It works very well. The shaft is long. It reaches deep spots. I used it on a fan, too. The screws were hidden. This tool reached them with ease. The bits held the screw tight. I did not drop any parts. That saved me time. I hate when screws fall. This tool solved that problem.

I checked the bit strength. Some tools get loose. The bits fall out. This one stays tight. I fixed a door lock. The screws were stuck. I pushed hard on the handle. The bit did not slip. It did not strip the screw. The handle has a good grip. It does not hurt my hand.

But I missed one thing. It has no square bits. I tried to fix a deck. The screws were square drive. This tool could not help. I had to get another one. This tool is great for normal screws. It fits Phillips and Flat heads. It is perfect for most home jobs. Just know it lacks square tips.

Klein 32560 Review: Best For HVAC Jobs

I needed square bits for a job. So I bought the Klein 32560. It looks like the other one. The handle is yellow and black. The shaft is long, too. But the bits are different. This one is made for pros. It has square drive tips.

I used it on a furnace. The panel used square screws. The 32560 fit them perfectly. It did not slip. A Phillips bit would strip them. This square bit held firm. I felt safe using it. I also used the nut driver. I took off a gas valve panel. The long shaft helped a lot. I could reach past the pipes.

There is a trade-off. You lose the small flat bit. I tried to fix a knob. The screw was tiny. The 32560 bit was too big. I could not turn it. That was annoying. I had to find a small driver.

But for wire work, it is great. I tightened an outlet. The square bit grabbed well. I could crank it down. The handle is soft. It does not dig into your palm. If you do electrical work, get this one. The bit choice is better for you. You just lose the small tips.

Details Comparison for Klein 32559 vs 32560

Which tool is for you? They feel the same. But they work on different screws. Here are five key points.

The Bit Types

This is the main change. The 32559 has standard bits. It fits most home screws. The 32560 has square bits. Pros use these a lot. Check your screws first. Pick the one that fits your work.

Shaft Reach

Both tools are long. They reach four inches out. This is longer than normal. I measured both of them. They are the exact same length.

I tested them on a light. The screws were high up. A short tool hits the rim. These long tools slide right in. It saves your knuckles. The tube is thick steel. It is very strong. But it might not fit tiny holes.

Grip Feel

I like the grip. It is soft rubber. It has ribs on it. This helps you hold it. Both tools use the same handle.

I tested the torque. I drove a long screw into wood. My hand did not slip. I could push hard. The handle is wide. This gives you power. It does not hurt your hand. It feels balanced.

Holding Power

Loose bits are bad. I checked both tools. I shook them hard. I dropped them on the floor. The bits stayed in the tube.

They use a small ball. It clicks the bit in. It holds very tight. After weeks, it is still good. It does not wobble much. This helps you aim. You can use it with one hand.

The Cost

Both cost about the same. They are a good value. You pay for good steel. The tips last a long time.

If you buy the 32559, you might need square bits. That adds cost later. If you buy the 32560, you might need a small flathead. Think about what you own. Pick the one that fills the gap.

Conclusion

Get the Klein 32559 for home use. It fits the screws you see most. It is a great general tool. Get the Klein 32560 for HVAC work. You will need those square bits. Both are well made. They will last for years.