Dewalt dwe575 vs Makita 5007mg: My Real Test

Dewalt dwe575 vs Makita 5007mg is a big choice. My name is Maruf. I test tools for real work. I used both saws for a few weeks. Here is what I found.

DeWalt DWE575 Hands On Review

I took the DeWalt to a new job site. We built a large wood shed. I had to cut a lot of pine boards. I also cut thick oak wood. I used the saw all day long. This saw is very light. It weighs less than nine pounds. This low weight is a big help. My right arm did not hurt at all. My wrist felt fine at the end of the day.

This is great for a long work shift. I made deep cuts in the thick oak. The saw did not slow down once. The motor sounds very strong. The base is flat and very stiff. It is made of good metal. It slides well on rough wood. I checked my cut lines often. The cuts were very clean and straight.

I kept using it for two more weeks. I put it through hard tests. I dropped it one time in the dirt. It fell hard on the ground. It got a small scratch on the base. But it still cut a straight line. The dust blower is a very nice touch. It blows the wood dust off my mark. I never had to blow the dust with my mouth.

The power cord is very thick. It does not rip or tear easily. I pulled the saw up by the cord. The cord held up fine. It is a very simple tool to use. It has no fancy lights or screens. But it does the hard work very well. I trust it for fast jobs. It gets the work done right.

Makita 5007MG Hands On Review

Next, I tried the Makita saw. I know this brand makes very tough tools. I wanted to see if it was worth the high cost. I used it to cut wet, heavy wood. I built a large deck in a back yard. The wood was soaked with rain. The motor on this saw spins very fast. It cuts wet wood like a hot knife in butter.

The blade did not get stuck at all. The saw feels very smooth in my hand. It does not shake or jump much. But it is a very heavy tool. It weighs over ten pounds.

My arm got tired fast. I had to rest my wrist a lot. But I really loved the bright lights. The two lights show the cut line so well. I worked late into the dark one night. I did not need a big work light. I could still see my marks clearly. The base is a strong, light metal. It took a hard hit in the back of my truck.

A heavy box fell on it. It did not bend or warp at all. The grips use thick, soft rubber. They feel great in my bare hands. The cord is very soft in cold air. It does not get stiff. It is a very tough saw for hard jobs. I trust it for big cuts.

Detailed Comparison for Dewalt dwe575 vs Makita 5007mg

Let us look close at dewalt dwe575 vs makita 5007mg. I will show how they act on a real job.

Core Work Power

Let us look at how much power they have. Both saws cut thick wood very fast. They both use a strong motor. The motor draws a lot of amps. The Makita cuts a bit smoother than the DeWalt. The Makita blade spins much faster. This fast speed helps on thin sheets of wood. It leaves a very clean edge. The wood does not break.

The DeWalt cuts a tiny bit deeper. I saw this when I cut thick roof beams. I had to cut at a sharp angle. The DeWalt went all the way through. The Makita stopped short by a hair. The DeWalt is best for all day work. The Makita is best for thick, wet wood.

Cut True and Straight

A good saw must cut a straight line. It must do this every single time. I checked both saws with a smart tool. I set them to cut at an angle. The Makita stayed perfectly straight. It did not shift after I made hard cuts. The heavy weight helps a lot here. It keeps the saw flat on the wood.

It does not bounce around. The DeWalt was very good too. But it needed a small fix after I dropped it. The metal bent just a tiny bit. I had to use a tool to make it square again. The Makita is the clear winner for true cuts. It holds its shape very well.

Size and Real Feel

How a tool feels in the hand is a huge deal. I hold these saws for eight hours a day. The DeWalt wins for low weight and real comfort. It is a true joy to hold in one hand. It balances very well from front to back. The Makita is very bulky and thick. It makes my wrist hurt after just an hour.

I have to use two hands a lot. But the Makita grip is much better made. The thick rubber feels very soft and safe. My hand does not slip when I sweat. The DeWalt uses hard plastic on the grip. It can slip if my hand is wet.

Lights and Easy Use

We do not get fancy screens on these saws. But we do get clear marks and lights. The Makita wins big in this test. The two bright lights are truly great. They show exactly where the blade will go. They light up the dark corners of a room. The DeWalt has no light at all. This is a big let down.

The Makita marks are painted black on the metal. I can read them fast in the bright sun. The DeWalt marks are hard to read. They are just stamped in the bare metal. You have to tilt the saw to see them. The Makita is much easier to set up fast.

Tough Build Quality

I look hard at the parts that break fast. A job site is a tough place for tools. The Makita uses top grade metal for the base. The guard and shoe are very hard to bend. They can take a real beating. The DeWalt uses a more basic soft metal. It can scratch on rough floors.

The Makita levers are large and thick. I can move them fast with thick work gloves on. The DeWalt has small thin metal levers. They are hard to grab with gloves. The Makita feels like a high end premium tool. The DeWalt feels like a basic work horse. Both will last a long time if you care for them.

Both saws do great work on a real site. The DeWalt is best for fast, light cuts. The Makita is best for smooth cuts in bad light. You will be happy with either tool.